1978 Siphonic Jet flushing CUPC one-piece Toilet
Size:690x370x700mm,
S trap 300mm roughing in only
Single flush 1.28GPF / 4.8LPF
Top Push or Lateral
About 380pcs per 40HC container
Quotation with soft seat cover and R&T tank fitting.
| Place of Origin |
Chaozhou,Guangdong |
Model Number: |
1978 |
| Material: |
Ceramic |
outlet: |
S trap, 300mm |
| Seat cover: |
Yes |
Tank Titting: |
Top push or Lateral |
| Packing: |
Carton Box |
Grade: |
A Grade |
| OEM/ODM: |
Avaliable |
Installation: |
floor |
Identication: Each ?xture shall be marked with the marking requirements of the applicable performance standard. The product packaging
shall bear the EPA-IAPMO WaterSense label.
Characteristics: Gravity feed vitreous china water closets manufactured in compliance to EPA's WaterSense Tank-Type High E?ciency Toilet
Speci?cation that are equipped with an IAPMO R&T listed anti-siphon ballcock and ?ush valves, and to be installed in
accordance with the manufacturer's instructions.
Products listed on this certi?cate have been tested by an IAPMO R&T recognized laboratory. This recognition has been
granted based upon the laboratory's compliance to the applicable requirements of ISO/IEC 17025.
Products are certi?ed to the following standard(s):
EPA WaterSense Speci?cation for Tank-Type Toilets (Version 1.2, June 2, 2014)
Identification:
Water Closets with Dual Flush Feature shall be marked with the manufacturer's name or registered trademark, or in the case of
private labeling, the name of the customer for whom the fixture was manufactured. Markings shall be permanent, legible, and
visible after installation.
The model number of close-coupled water closets shall be marked on both the tank and the bowl.
Water closets with Dual Flush Feature shall be marked to identify the average water consumption, expressed in litres and
gallons per flush. The litre or gallon value may be stated first, at the manufacturer's option. The product shall be marked with the
reduced flush volume and the designation ASME A112.19.14 to signify compliance with this Standard. The location of this mark
shall be determined by the manufacturer and is not required to be permanent, but it shall be visible after installation. The label
shall be intended for removal by the occupant only, and this shall be so stated on the label.
Gravity flush tanks shall be marked with a water level mark or with the information necessary to determine the water level in the
tank needed to deliver the intended flush volume. This mark shall be applied to the ceramic body of the tank, the tank liner, or
the flush valve overflow tube. The vertical distance between the water level mark and the lowest point of the tank overflow
channel shall not exceed 38 mm (1.5 in).
Water closet tanks shall have a label indicating at least the following:
(a) the telephone number or contact information of a service department from which end-users can obtain replacement parts;
(b) the serial or part number of the flush valve seal; and
(c) information on procuring replacement parts for maintaining the original flush volume.
All packaging shall be marked with the manufacturer's name or registered trademark; or in case of private labeling, the name of
the customer for whom the fixture was manufactured and the model number. Packaging shall be marked with the water
consumption in gpf and Lpf.
Each fixture shall be marked with the cUPC® certification mark. In the case where the tank and the bowl are sold separately,
both shall have the certification mark.
Identification of flush mode options shall be depicted on the actuator. This identification shall be either by graphic display or
lettering, or shall be intuitively apparent.
Fixtures that require proprietary (i.e., non-standard) components, e.g., supply fittings, waste fittings, or water closet seats, shall
indicate, in the packaging or the accompanying literature, that such components are provided by the manufacturer and shall
identify the proper replacement parts.
Fixtures that do not comply with one or more of the dimensional requirements of this Standard shall be marked with an "N" to
indicate the non-standard nature of the fixture.
Characteristics:
To be installed in accordance with the manufacturer's instructions, the latest edition of the Uniform Plumbing Code, and the
National Plumbing Code of Canada.
Audited Supplier 
){kind=link}